Wi-Fi devices require specific network conditions to connect successfully. Some modems, particularly Telstra modems, will require changes to their Wi-Fi settings before pairing can be completed.
We highly recommend using a dedicated 2.4GHz Guest Network for your device where possible.
Important information for WX Tap Timer Hub users
The Wi-Fi chip used in the WX Tap Timer Hub changed in late 2025. Hubs using the newer chip are more sensitive to network configuration than the previous version and are currently the most sensitive of our Wi-Fi devices.
If an older WX Hub or another Holman Wi-Fi device connects successfully to your network, this does not necessarily mean a newer WX Hub will connect using the same modem settings.
If you are having difficulty pairing a newer WX Hub, please work through the network requirements below.
Step 1: Prepare Your Phone
Before starting the pairing process, prevent your phone from automatically changing networks during setup.
Turn off Mobile Data
Disable mobile data on your phone so it doesn't try to switch back to an internet-connected network while communicating with the device.
Disable Auto-Join / Auto-Reconnect
- iOS: Turn off Auto-Join
- Android: Turn off Auto-Reconnect
Go to your phone's Wi-Fi settings and disable this for any networks that automatically connect. This helps prevent your phone from jumping away from the device's Wi-Fi signal during pairing and is a more common requirement for iPhones.
Step 2: Use AP Mode
When pairing the device in the Holman Home app, select AP Mode.
AP Mode is generally more reliable than the standard pairing method, particularly with modern home networks.
Step 3: Check Your Modem Settings
Your modem must meet the following Wi-Fi requirements for the device to connect.
✅ 2.4GHz Wi-Fi
- Holman Wi-Fi devices connect using 2.4GHz Wi-Fi.
- If possible, create a dedicated 2.4GHz Guest Network for the device.
- This is often the easiest option because it allows you to configure a compatible network without changing your main home Wi-Fi network.
✅ WPA2 Security
- Wi-Fi security should be set to WPA2 or WPA2-PSK.
- WPA3 can prevent the device from connecting.
✅ Disable Band Steering
Band Steering combines or automatically directs devices between the 2.4GHz and 5GHz Wi-Fi bands.
This can interfere with pairing and should be disabled for the network being used by the device.
✅ Disable PMF (Protected Management Frames)
PMF can prevent compatible devices from successfully connecting.
If PMF is set to Enabled or Required, change it to Disabled for the network being used to connect the device.
Telstra Modems
If you are using a Telstra modem, you will need to change the modem's Wi-Fi settings to meet the requirements above.
The fact that another Holman device, or an older WX Tap Timer Hub, has previously connected successfully does not confirm that the modem is correctly configured for newer devices.
More details on the required modem settings can be found in the Holman Home app during the pairing process by selecting "Help Me Prepare".
What Happens When the Pairing Process Finishes?
If you have followed all of the steps above, one of the following will occur.
✅ The Hub Stops Flashing
If the Hub stops flashing during the pairing process, it has probably connected successfully.
Allow the pairing process in the app to finish, then:
- Reconnect your phone to your 2.4GHz home Wi-Fi network.
- Return to the Holman Home app.
- Check All Devices.
The Hub will likely appear under All Devices, even if the pairing process initially reports "Failed to add".
❌ The Hub Continues Flashing
If the Hub does not stop flashing, check your phone's Wi-Fi settings and see what network it is connected to.
1. Your phone is still connected to your home Wi-Fi
This indicates that either:
- the AP Mode pairing steps were not completed correctly, or
- Auto-Join / Auto-Reconnect is still enabled for your home Wi-Fi network.
Go back through the steps above before attempting to pair again.
2. Your phone is not connected to any Wi-Fi network
This indicates that the connection between the Hub and your modem has failed and is consistent with a modem compatibility or configuration issue.
Check that your modem meets all of the requirements listed above, particularly 2.4GHz, WPA2, Band Steering and PMF settings.
3. Your phone is connected to the Holman / Smart Life Wi-Fi hotspot
This is okay. The Holman / Smart Life hotspot may have Auto-Join enabled, and this does not need to be disabled for pairing.
If the Hub is still flashing, this generally means the Hub was unable to connect to your modem, so the actual result is effectively the same as Result 2 above.
Need Help?
Because modem interfaces and settings vary between manufacturers and internet providers, Holman Technical Support cannot guide you through changing the settings of your specific modem.
If you need assistance changing your modem's Wi-Fi configuration, please contact your internet service provider (ISP).
We can, however, assist you with Holman Home app setup and device pairing.
📞 Call us: 1300 716 188
🕒 Available: 7:00am – 3:30pm AWST